ACV STALK MB ISO Audio 10

Stalk Adapter Mercedes / VW 

Keep the original steering wheel remote control functions when replacing the factory radio with a retrofit HU.

Depending on the vehicle equipment as well as the range of functions and software of the retrofit HU, individual operating functions may be omitted or replaced by other functions.

Compare the pictured harness connectors with the connectors in your car and make sure that they fit optically and technically.

Check if one of the listed OEM head units were installed originally.

Also check vehicle functionality, vehicle settings and SWC functionality before final assembly.

Please contact our support team for help
02431-9645-96
support@acvgmbh.de

Note:

CAN Bus

connector: ISO / 10 Pin ISO / Mini ISO Mercedes

check dip switches for retrofit HU

vehicles Mercedes with Audio 5 / Audio 10 1-DIN OEM HU
vehicles Mercedes with Audio 30 APS 1-DIN OEM Sat Nav
vehicles Mercedes with Comand 2.0 OEM Sat Nav

vehicles VW Crafter with RCD 2001 1-DIN OEM HU

vehicles Mercedes / VW with open dash > check connection and assignment by measuring before installation with OEM HU:
incorrect connection damages the interface

vehicles with different comfort interior CAN bus connection:
brown-red twisted: CAN high   
brown twisted: CAN low 

CAN Bus in CAN Bus distributor under sill cover
CAN Bus at climatronic
CAN Bus in Mini ISO connector: Pin 2 CAN high / Pin 1 CAN low 
CAN Bus in 8 Pin power connector: Pin 7 CAN high / Pin 6 CAN low

vehicles with Comand 2.0 OEM Sat Nav:
CAN Bus in 18 Pin AMP connector: Pin 9 CAN high / Pin 8 CAN low / not Robert Bosch CAN

OEM HU with ISO block connector:
ISO extension harness speaker 10cm> item: 1322-02

vehicles with 10 Pin ISO / ISO speaker connector OEM amplified system without B2B optical system OEM amplified system:
Active system adapter different vehicles ISO>ISO > item: 13-1190-50

Vehicle application:

• Mercedes A-class (W169) 10/2004 - 04/2012
• Mercedes A-class (C169) 11/2004 - 07/2011
• Mercedes B-class (T245) 06/2005 - 06/2011
• Mercedes C-class (W203) 03/2000 - 01/2005
• Mercedes CLK-class (C208) 07/1999 - 03/2003
• Mercedes CLK-class (C209) 03/2002 - 05/2005
• Mercedes E-class (W210) 06/1999 - 12/2002
• Mercedes SL-class (R230) 08/2001 - 02/2006
• Mercedes SLR (C199) 12/2003 - 12/2009
• Mercedes Sprinter (W906) 04/2006 - 08/2013
• Mercedes Sprinter (W906) 08/2013 - 05/2018
• Mercedes Vito/Viano (W639) 07/2003 - 08/2010
• Mercedes Vito/Viano (W639) 09/2010 - 03/2014

VW

• VW Crafter I (2EC/2EK/2F) 03/2006 - 07/2011
• VW Crafter I (2EC/2EK/2F) 07/2011 - 11/2016

Following signals are provided:

Reimported vehicles or vehicles with different software may be incompatible in functions.

pink: +12V ignition clamp 15 1,5A max.
orange: +12V illumination clamp 58 0,1A max.
white: +12V reverse gear signal 1,5A max.
yellow/green yellow/red: speed pulse signal

SWC

HU application:
 
Multilead different HU > item: 42arc100

Alpine 3,5mm jack connector > item: 42arc101
Blaupunkt 2010> 3,5mm jack connector > item: 42arc107
Blaupunkt 2010> Key1 / Key2 / (GND) connector > item: 42arc000
China Hu Key1 / Key2 / (GND) > item: 42arc000
Clarion 3,5mm jack connector > item: 42arc104
Digital Dynamics single lead connector > item: 42arc108
ESX Key1 / Key2 connector > item: 42arc000
JVC 3,5mm jack connector > item: 42arc104
JVC single lead connector > item: 42arc105
Kenwood single lead connector > item: 42arc105
Kenwood 2017> 3,5mm jack connector > item: 42arc107
Kenwood 2020> Key1 / Key2 / GND connector > item: 42arc000
Pioneer 3,5mm jack connector > item: 42arc107
Pioneer AVH/DMH/SPH 3,5mm jack connector > item: 42arc1072
Snooper Key1 / Key2 connector > item: 42arc000
Sony 3,5mm jack connector > item: 42arc107
XZent single lead connector > item: 42arc108
Zenec single lead connector > item: 42arc108

---

General installation instructions:

Verification:
1: Check all operating functions and vehicle setting functions of the OEM HU.
2: Disconnect the OEM HU voltage-free.
3: Check all interface connections for correctness voltage-free.

Connection and connection sequence:
1: Check settings and hardware configuration of the interface voltage-free.
2: Check configuration of the HU connection cable voltage-free.
3: Connect the HU connection cable according to the operating instructions of the retrofit HU.
4: Connect all other connections according to the operating instructions of the retrofit HU.
5: Connect the entire installation to the vehicle with the main connection last.
6: Software configuration of the interface according to the instructions in the item text and in the manual.
7: Configure the retrofit HU according to the operating instructions of the retrofit device steering wheel remote control/camera/handsfree kit/antenna phantom powering and others.
8: Function test of steering wheel remote control and vehicle

Changes to the configuration of the interface and the HU connection cable:
1: Change configuration voltage-free
2: Reconnection see above 5 to 8

In case of malfunction of the interface or the vehicle:
1: Reinstall the OEM HU
2: Operate the OEM HU
3: Establish CAN bus shut down
4: Check the hardware configuration of the interface
5: Reconnection after CAN Bus shut down see above 5 and 6

More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist installer.

More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
1: Connections and changes are to be carried out exclusively by trained specialist installer.
2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.
3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle's cable assignment diagram before connection.
4: Connections and modifications are made on the user's own responsibility without guarantee of function.
5: Connections and modifications are made on the user's own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface.
6: Modifications to the pre-assembled wiring harness may invalidate the product's warranty.